TC74LCX374FT(EL)
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Digi-Reel® |
| Published | 1998 |
| Series | 74LCX |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.635mm |
| Reach Compliance Code | unknown |
| Base Part Number | 74LCX374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 3.3V |
| Load Capacitance | 50pF |
| Clock Frequency | 150MHz |
| Propagation Delay | 8.5 ns |
| Quiescent Current | 10μA |
| Turn On Delay Time | 1.5 ns |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 7pF |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | Non-RoHS Compliant |
TC74LCX374FT(EL) Overview
The item is packaged in 20-TSSOP (0.173, 4.40mm Width)cases. As part of the package Digi-Reel?, it is embedded. As configured, the output uses Tri-State, Non-Inverted. This trigger uses the value Positive Edge. It is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2V~3.6V. It is operating at -40°C~85°C TA. A flip flop of this type is classified as a D-Type. In FPGA terms, D flip flop is a type of 74LCXseries FPGA. A frequency of 150MHzshould not be exceeded by its output. A total of 1elements are contained within it. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. Members of the 74LCX374family make up this object. Power is supplied from a voltage of 3.3V volts. A JK flip flop with a 7pFfarad input capacitance is used here. A part of the electronic system is mounted in the way of Surface Mount. There are 20pins on it. This device has Positive Edgeas its clock edge trigger type. There is a base part number FF/Latchesfor the RS flip flops. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. There are 3.3V power supplies attached to it. 10μAquiescent current consumed.
TC74LCX374FT(EL) Features
Digi-Reel? package
74LCX series
20 pins
3.3V power supplies
TC74LCX374FT(EL) Applications
There are a lot of Toshiba Semiconductor and Storage TC74LCX374FT(EL) Flip Flops applications.
- Balanced 24 mA output drivers
- ATE
- Bounce elimination switch
- Convert a momentary switch to a toggle switch
- Count Modes
- Shift registers
- Frequency Dividers
- Digital electronics systems
- Memory
- Set-reset capability
