TC7WT74FUTE12LF
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.110, 2.80mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| Series | TC7WT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Base Part Number | 7WT74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 1 |
| Load Capacitance | 50pF |
| Clock Frequency | 53MHz |
| Propagation Delay | 30 ns |
| Quiescent Current | 2μA |
| Turn On Delay Time | 17 ns |
| Logic Function | AND, D-Type |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 30ns @ 5.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
TC7WT74FUTE12LF Overview
It is embeded in 8-TSSOP, 8-MSOP (0.110, 2.80mm Width) case. The Tape & Reel (TR)package contains it. It is configured with Differentialas an output. This trigger is configured to use Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. A temperature of -40°C~85°C TAis considered to be the operating temperature. It is an electronic flip flop with the type D-Type. In terms of FPGAs, it belongs to the TC7WT series. You should not exceed 53MHzin the output frequency of the device. A total of 8terminations have been recorded. The 7WT74family includes it. A voltage of 5V is used as the power supply for this D latch. Input capacitance of this device is 5pF farads. The electronic part is mounted in the way of Surface Mount. With its 8pins, it is designed to work with most electronic flip flops. This device exhibits a clock edge trigger type of Positive Edge. The RS flip flops belongs to FF/Latches base part number. The superior flexibility of this circuit is achieved by using 1 circuits. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. The system runs on a power supply of 5V watts. If high efficiency is desired, the supply voltage should be kept at 5V. Quiescent current is consumed by the D latch in the amount of 2μA.
TC7WT74FUTE12LF Features
Tape & Reel (TR) package
TC7WT series
8 pins
5V power supplies
TC7WT74FUTE12LF Applications
There are a lot of Toshiba Semiconductor and Storage TC7WT74FUTE12LF Flip Flops applications.
- Count Modes
- Event Detectors
- Automotive
- Individual Asynchronous Resets
- Circuit Design
- Reduced system switching noise
- ESCC
- Shift registers
- High Performance Logic for test systems
- Memory
