TCM810JVNB713
| Parameters | |
|---|---|
| Min Reset Threshold Voltage | 3.93V |
| Max Reset Threshold Voltage | 4.06V |
| Threshold Voltage | +4V |
| Undervoltage Threshold | 3.93V |
| Overvoltage Threshold | 4.06V |
| Height | 1.02mm |
| Length | 3.04mm |
| Width | 1.4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.96mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | TCM810 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 12μA |
| Nominal Supply Current | 12μA |
| Power Dissipation | 320mW |
| Adjustable Threshold | NO |
| Quiescent Current | 12μA |
| Watchdog Timer | No |
| Reset | Active High |
| Voltage - Threshold | 4V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
TCM810JVNB713 Overview
There are 3 terminals on this power management that allow it to be mounted. Packaging is in the form of a Tape & Reel (TR). As a reference, this IC management includes 1 functions for your convenience. Power management consists of 1 channels, each of which can be used independently. In this PMIC, you can find TO-236-3, SC-59, SOT-23-3 functions for your reference. This IC power shares lots of benefits with other Simple Reset/Power-On Reset products. IC management is specified that the package peak reflow temperature should be 260. When a supply voltage of 5V is applied to the power ic, it conducts. During operation, the power ic is supplied with a voltage of 1. The mount is provided by Surface Mount. A IC power such as this can be classified as a Power Management Circuits power management system. It has a total of 3 pins that are attached to IC management. Pin count of the power management is 3. In order for this IC power to function, the supply voltage (Vsup) cannot be less than 1V. There should be no more than 5.5V volts of supply voltage (Vsup) in this power management. The recommended mounting type for IC management is Surface Mount. It is recommended that the supervisor be set to this temperature: -40°C~125°C TA. While this power management is operating, it will output Push-Pull, Totem Pole as the output voltage. Supplied with a operating current of 12μA, this PMIC is capable of fully function as specified. A similar IC managements number of the manufacturer can always be found by using TCM810, the base power ics number. A power supply of 5V watts is required for the operation of this power management.
TCM810JVNB713 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
12μA operating supply current
TCM810JVNB713 Applications
There are a lot of Microchip Technology TCM810JVNB713 Voltage Supervisors applications.
- Sensitive sensors
- Consumer electronics
- Detection of phase imbalance
- Detection of phase sequence
- WiFi router
- DVR
- Battery cars
- Analog circuit
- Automotive permanent magnet synchronous motors
- Medical-specific isolation transformer
