Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
Surface Mount |
YES |
Number of Pins |
8 |
Weight |
24.408939mg |
Operating Temperature |
-40°C~85°C |
Packaging |
Tube |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Max Power Dissipation |
2.14W |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Base Part Number |
THS4011 |
Pin Count |
8 |
Number of Elements |
1 |
Operating Supply Current |
7.8mA |
Nominal Supply Current |
9.5mA |
Power Dissipation |
2.14W |
Slew Rate |
310V/μs |
Amplifier Type |
Voltage Feedback |
Common Mode Rejection Ratio |
90 dB |
Current - Input Bias |
2μA |
Voltage - Supply, Single/Dual (±) |
9V~32V ±4.5V~16V |
Output Current per Channel |
110mA |
Input Offset Voltage (Vos) |
6mV |
Bandwidth |
290MHz |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Unity Gain BW-Nom |
290000 kHz |
Voltage Gain |
81.58dB |
Power Supply Rejection Ratio (PSRR) |
75dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
1mV |
Settling Time |
37 ns |
Low-Bias |
NO |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
6μA |
Programmable Power |
NO |
Max I/O Voltage |
6mV |
Input Offset Current-Max (IIO) |
0.25μA |
Height |
1.1mm |
Length |
3mm |
Width |
3mm |
Thickness |
1.02mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
THS4011IDGN Overview
Packaging for the buffer amplifier is in the form of a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad case. Voltage Feedback-type instrumentation amplifiers are used in this application. A Tube case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. Please take in mind that this instrumentation amplifier should be run at 15V. Instrumentation amplifier is a part of Operational Amplifier. A total of 8 pins are present on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 6mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . An 7.8mA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 81.58dB. There are 1 elements in total in this linear amplifier.
THS4011IDGN Features
8 Pins
supply voltage of 15V
81.58dB voltage gain
THS4011IDGN Applications
There are a lot of Texas Instruments THS4011IDGN Instrumentational OP Amps applications.
- Band-pass filter
- single/dual op amp sum and difference circuits
- Commercial audio systems
- Test equipment
- Portable electronic products powered by batteries
- Blood pressure sensors
- Precision measurement
- Division circuits
- Tablets
- Fast A/D and D/A converters