THS4031IDGNR
| Parameters | |
|---|---|
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | THS4031 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 8.5mA |
| Nominal Supply Current | 10mA |
| Power Dissipation | 1.8W |
| Slew Rate | 100V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 3μA |
| Voltage - Supply, Single/Dual (±) | 9V~32V ±4.5V~16V |
| Output Current per Channel | 90mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 100MHz |
| Gain Bandwidth Product | 120MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 200000 kHz |
| Voltage Gain | 95dB |
| Power Supply Rejection Ratio (PSRR) | 85dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Settling Time | 60 ns |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 90MHz |
| Bias Current-Max (IIB) @25C | 6μA |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.25μA |
| Height | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 1.02mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 24.408939mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 1.8W |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
THS4031IDGNR Overview
A 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad case is used to package the op amp. An op amp ic of the Voltage Feedback type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are located on this board. Please take in mind that op amp should be run at 15V. It should be noted that this op amp is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 2mV. The mounting type that is recommended for this electrical part is Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 8.5mA and 10 . Keeping the voltage gain at 95dB is the best course of action. There are 1 channels on the operational amplifiers. As a result of this, the buffer amplifier is packed in TR.
THS4031IDGNR Features
8 Pins
supply voltage of 15V
95dB voltage gain
THS4031IDGNR Applications
There are a lot of Texas Instruments THS4031IDGNR Instrumentational OP Amps applications.
- High speed sample
- Navigation
- Non-polarized electrodes
- Test and measurement instruments
- Wireless base stations
- Automotive sensors
- Large motor controllers
- Measurements of Wheatstone bridge
- Television broadcasting equipment
- Scintillation detectors
