banner_page

THS4052CDR

100mA per Channel 2.5μA 70 dB Instrumentational OP Amps 9V~32V ±4.5V~16V THS4052 8 Pins 8-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-THS4052CDR
  • Package: 8-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 434
  • Description: 100mA per Channel 2.5μA 70 dB Instrumentational OP Amps 9V~32V ±4.5V~16V THS4052 8 Pins 8-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 1 day ago)
Mounting Type Surface Mount
Package / Case 8-SOIC (0.154, 3.90mm Width)
Surface Mount YES
Number of Pins 8
Weight 75.891673mg
Operating Temperature 0°C~70°C
Packaging Tape & Reel (TR)
JESD-609 Code e4
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Operational Amplifier
Packing Method TR
Max Power Dissipation 740mW
Technology BIPOLAR
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 15V
Base Part Number THS4052
Pin Count 8
Number of Elements 2
Operating Supply Current 8.5mA
Nominal Supply Current 21mA
Power Dissipation 740mW
Slew Rate 240V/μs
Amplifier Type Voltage Feedback
Common Mode Rejection Ratio 70 dB
Current - Input Bias 2.5μA
Voltage - Supply, Single/Dual (±) 9V~32V ±4.5V~16V
Output Current per Channel 100mA
Input Offset Voltage (Vos) 10mV
Bandwidth 70MHz
Gain Bandwidth Product 70MHz
Neg Supply Voltage-Nom (Vsup) -15V
Unity Gain BW-Nom 70000 kHz
Voltage Gain 75.56dB
Power Supply Rejection Ratio (PSRR) 70dB
Low-Offset NO
Frequency Compensation YES
Supply Voltage Limit-Max 16.5V
Voltage - Input Offset 2.5mV
Settling Time 60 ns
Low-Bias NO
Micropower NO
-3db Bandwidth 38MHz
Bias Current-Max (IIB) @25C 6μA
Programmable Power NO
Neg Supply Voltage-Max (Vsup) -16.5V
Max I/O Voltage 10mV
Height 1.75mm
Length 4.9mm
Width 3.91mm
Thickness 1.58mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

THS4052CDR Overview


Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. A Voltage Feedback-type buffer amplifier is shown here. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are included on the operational amplifiers. The input offset voltage is 10mV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around 0°C~70°C . As long as the supply current of the chip does not exceed 8.5mA, this op amp ic can operate. It is recommended to keep the voltage gain at 75.56dB at all times. There are a total of 2 elements in this linear amplifier. A TR-shaped amplifier is used to pack the buffer amps.

THS4052CDR Features


8 Pins
supply voltage of 15V
75.56dB voltage gain

THS4052CDR Applications


There are a lot of Texas Instruments THS4052CDR Instrumentational OP Amps applications.

  • Band-stop filter
  • High/low-pass filter circuit
  • Test equipment
  • Strain gauges
  • High speed sample
  • Home audio systems
  • Communication device
  • High input resistance broadband
  • Automotive sensors
  • Signal filtering

Write a review

Note: HTML is not translated!
    Bad           Good