THS4121IDGNR
| Parameters | |
|---|---|
| Operating Supply Voltage | 3.3V |
| Number of Elements | 1 |
| Operating Supply Current | 11mA |
| Nominal Supply Current | 13.5mA |
| Power Dissipation | 1.71W |
| Slew Rate | 55V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 64 dB |
| Current - Input Bias | 1.2pA |
| Max Input Voltage | -100mV |
| Voltage - Supply, Single/Dual (±) | 3V~3.5V ±1.5V~1.75V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 8mV |
| Bandwidth | 100MHz |
| Gain Bandwidth Product | 100MHz |
| Unity Gain BW-Nom | 100000 kHz |
| Voltage Gain | 66dB |
| Power Supply Rejection Ratio (PSRR) | 68dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 3.6V |
| Voltage - Input Offset | 3mV |
| Settling Time | 60 ns |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 100MHz |
| Programmable Power | NO |
| Dual Supply Voltage | 1.65V |
| Max I/O Voltage | 8mV |
| Height | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 1.02mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 24.408939mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 820MOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 1.71W |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | THS4121 |
| Pin Count | 8 |
THS4121IDGNR Overview
It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad-case that protects the operational amplifiers from damage. Op amps are Differential types of amplifier on the chip. Linear amplifier is delivered in a Cut Tape (CT) case. A total of 8 terminations have been reported in the past few weeks. The pins on this board total to 8 in total. This linear amplifier should be powered by an 3.3V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The buffer op amp includes 8 pins. Op amp ic rates 8mV for input offset voltage. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. A supply current of 11mA can be used to operate this linear amplifier. There should be no change in the voltage gain at 66dB. As a whole, there are 1 elements that make up this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 3.3V voltage. An buffer amplifier is packed in a TR-shape according to the design. Instrumentation amplifier resistance should stay within the range of 820MOhm.
THS4121IDGNR Features
8 Pins
supply voltage of 3.3V
66dB voltage gain
Resistance of 820MOhm
THS4121IDGNR Applications
There are a lot of Texas Instruments THS4121IDGNR Instrumentational OP Amps applications.
- Weighing systems
- Exponential operation circuits
- Signal transformation
- Power control
- Gaming industry
- Large motor controllers
- Portable media players
- Vehicle electronics
- Cinema or auditorium audio system
- ECG equipment
