THS4130IDGKG4
| Parameters | |
|---|---|
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 150MHz |
| Gain Bandwidth Product | 225MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 170000 kHz |
| Voltage Gain | 78dB |
| Average Bias Current-Max (IIB) | 6μA |
| Power Supply Rejection Ratio (PSRR) | 73dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Settling Time | 78 ns |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 80MHz |
| Bias Current-Max (IIB) @25C | 6μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.5μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 23.303308mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 34MOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 385mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | THS4130 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Elements | 1 |
| Operating Supply Current | 12.3mA |
| Nominal Supply Current | 15mA |
| Power Dissipation | 385mW |
| Min Input Voltage | 1.23V |
| Slew Rate | 52V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 2μA |
| Max Input Voltage | -700mV |
| Voltage - Supply, Single/Dual (±) | 4V~33V ±2V~16.5V |
| Output Current per Channel | 85mA |
THS4130IDGKG4 Overview
Packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case, the buffer op amp is ready to use. An op amp of this type is a Differential-type. A Tube case is used for delivering the op amp. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are located on this board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The op amp ic has an array of 8 pins on it. With regards to the offset voltage of the input, buffer amplifier is rated at 2mV. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Operational amplifier can operate supply current at 12.3mA. There should be no change in the voltage gain at 78dB. As a whole, there are 1 elements that make up this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 15V voltage. Op amp resistance should stay within the range of 34MOhm.
THS4130IDGKG4 Features
8 Pins
supply voltage of 5V
78dB voltage gain
Resistance of 34MOhm
THS4130IDGKG4 Applications
There are a lot of Texas Instruments THS4130IDGKG4 Instrumentational OP Amps applications.
- Vehicle electronics
- Proportional operation circuits
- Industrial control system
- ECG equipment
- Portable docking station
- High speed sample
- Measurements of Wheatstone bridge
- Weak signal detection
- Test and measurement instruments
- Weighing systems
