THS4131CDGNRG4
| Parameters | |
|---|---|
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 80MHz |
| Bias Current-Max (IIB) @25C | 6μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.5μA |
| Height | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 1.02mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 24.408939mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 34MOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 1.71W |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | THS4131 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Elements | 1 |
| Operating Supply Current | 12.3mA |
| Nominal Supply Current | 15mA |
| Power Dissipation | 1.71W |
| Min Input Voltage | 1.23V |
| Slew Rate | 52V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 2μA |
| Max Input Voltage | -700mV |
| Voltage - Supply, Single/Dual (±) | 4V~33V ±2V~16.5V |
| Output Current per Channel | 85mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 150MHz |
| Gain Bandwidth Product | 225MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 170000 kHz |
| Voltage Gain | 78dB |
| Average Bias Current-Max (IIB) | 6μA |
| Power Supply Rejection Ratio (PSRR) | 73dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Settling Time | 78 ns |
THS4131CDGNRG4 Overview
Packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad case, the buffer op amp is ready to use. Op amps are Differential types of amplifier on the chip. A Tape & Reel (TR) case is used for delivering the op amp. We are approaching the 8h termination of the year. The total number of pins on linear amplifier is 8. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are available on the instrumentation amplifier. Op amp rates 2mV as input offset voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . An 12.3mA volt supply current is needed for this linear amplifier to operate. 78dB should be the voltage gain. There is a rating of 1 for the operating supply voltage of the buffer op amp. The operating supply voltage of the buffer op amp is rated at 15V. A TR-shaped amplifier is used to pack the buffer amps. Linear amplifier resistance should stay within the range of 34MOhm.
THS4131CDGNRG4 Features
8 Pins
supply voltage of 5V
78dB voltage gain
Resistance of 34MOhm
THS4131CDGNRG4 Applications
There are a lot of Texas Instruments THS4131CDGNRG4 Instrumentational OP Amps applications.
- Weak signal detection
- Non-polarized electrodes
- Measurements of Wheatstone bridge
- single/dual op amp sum and difference circuits
- Blood pressure sensors
- Portable electronic products powered by batteries
- Thermocouples
- earphone
- Portable media players
- PDA
