THS4131IDGKG4
| Parameters | |
|---|---|
| Current - Input Bias | 2μA |
| Max Input Voltage | -700mV |
| Voltage - Supply, Single/Dual (±) | 4V~33V ±2V~16.5V |
| Output Current per Channel | 85mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 150MHz |
| Gain Bandwidth Product | 225MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 170000 kHz |
| Voltage Gain | 78dB |
| Average Bias Current-Max (IIB) | 6μA |
| Power Supply Rejection Ratio (PSRR) | 73dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Settling Time | 78 ns |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 80MHz |
| Bias Current-Max (IIB) @25C | 6μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.5μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 23.303308mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 34MOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 385mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | THS4131 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Operating Supply Current | 12.3mA |
| Nominal Supply Current | 15mA |
| Power Dissipation | 385mW |
| Min Input Voltage | 1.23V |
| Slew Rate | 52V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 80 dB |
THS4131IDGKG4 Overview
A 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case is used to package the op amp. Buffer amps of this type are called Differential-types. A Tube case is used for delivering the op amp. The number of terminations is approaching the 8 mark. Linear amplifier has a total of 8 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. There are 8 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 2mV. Surface Mount is the recommended mounting type of operational amplifiers. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. Using an 12.3mA supply current, this operational amplifier ics can be operated. Keeping the voltage gain at 78dB is the best course of action. As a whole, there are 1 elements that make up this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 5V. Instrumentation amplifier resistance should stay within the range of 34MOhm.
THS4131IDGKG4 Features
8 Pins
supply voltage of 5V
78dB voltage gain
Resistance of 34MOhm
THS4131IDGKG4 Applications
There are a lot of Texas Instruments THS4131IDGKG4 Instrumentational OP Amps applications.
- Automotive sensors
- Home audio systems
- Proportional operation circuits
- Inverse/same-phase proportional circuit
- Gaming industry
- High input resistance broadband
- Band-stop filter
- Signal operation
- pH (acidity)
- Multiplication circuits
