THS4151ID
| Parameters | |
|---|---|
| Base Part Number | THS4151 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 30V |
| Number of Channels | 1 |
| Operating Supply Current | 17.5mA |
| Nominal Supply Current | 21mA |
| Power Dissipation | 1.02W |
| Slew Rate | 650V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 4.3μA |
| Voltage - Supply, Single/Dual (±) | 4V~33V ±2V~16.5V |
| Output Current per Channel | 85mA |
| Input Offset Voltage (Vos) | 7mV |
| Bandwidth | 150MHz |
| Gain Bandwidth Product | 340MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 150000 kHz |
| Voltage Gain | 67dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Settling Time | 53 ns |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 80MHz |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Max I/O Voltage | 7mV |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 75.891673mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 14.4MOhm |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 1.02W |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
THS4151ID Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. There are two types of operational amplifiers in this circuit. In the case of Tube cases, linear amplifier will be delivered. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. Op amp rates 7mV as input offset voltage. The mounting type that is recommended for this electrical part is Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureThis op amp can operate from a supply current at 17.5mA. It is recommended to keep the voltage gain at 67dB at all times. As far as the device is concerned, buffer amplifier has 1 channels. The operating supply voltage of the buffer op amp is rated at 30V. 14.4MOhm should be the range of resistance for the linear amplifier.
THS4151ID Features
8 Pins
supply voltage of 15V
67dB voltage gain
Resistance of 14.4MOhm
THS4151ID Applications
There are a lot of Texas Instruments THS4151ID Instrumentational OP Amps applications.
- High/low-pass filter circuit
- Power transmission
- Automotive sensors
- Measurements of Wheatstone bridge
- Subtraction operation circuits
- Addition operation circuits
- Active probe
- earphone
- High gain DC amplifier
- Television
