THS4211DRBTG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-VDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 22.906415mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 2.18W |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | THS4211 |
| Pin Count | 8 |
| Number of Elements | 1 |
| Operating Supply Current | 19mA |
| Power Dissipation | 2.18W |
| Supply Current-Max | 22mA |
| Slew Rate | 970V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 7μA |
| Voltage - Supply, Single/Dual (±) | 5V~15V ±2.5V~7.5V |
| Output Current per Channel | 220mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 350MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1000000 kHz |
| Voltage Gain | 68dB |
| Average Bias Current-Max (IIB) | 20μA |
| Power Supply Rejection Ratio (PSRR) | 58dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Settling Time | 22 ns |
| Low-Bias | NO |
| -3db Bandwidth | 325MHz |
| Programmable Power | NO |
| Max I/O Voltage | 3mV |
| Input Offset Current-Max (IIO) | 6μA |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 880μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
THS4211DRBTG4 Overview
It is packaged in an 8-VDFN Exposed Pad-case that protects the operational amplifiers from damage. The instrumentation amplifier in this picture is of the Voltage Feedback-type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. A total of 8 terminations have been reported in the past few weeks. Linear amplifier has a total of 8 pins. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. There are 8 pins on this chip. There is an input offset voltage of 3mV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. An 19mA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 68dB for the time being. The total number of elements in this buffer amplifier is 1. The instrumentation amplifier is packed in the form of TR.
THS4211DRBTG4 Features
8 Pins
supply voltage of 5V
68dB voltage gain
THS4211DRBTG4 Applications
There are a lot of Texas Instruments THS4211DRBTG4 Instrumentational OP Amps applications.
- Laptop
- Computer workstations
- High/low-pass filter circuit
- PDA
- Voltage regulation circuit
- Hand-held batteries
- Blood pressure sensors
- Proportional operation circuits
- Comparator
- Multiplication circuits
