THS4215DRBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-VDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 22.906415mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 2.18W |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | THS4215 |
| Pin Count | 8 |
| Number of Elements | 1 |
| Operating Supply Current | 19mA |
| Nominal Supply Current | 22mA |
| Power Dissipation | 2.18W |
| Slew Rate | 970V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 7μA |
| Voltage - Supply, Single/Dual (±) | 5V~15V ±2.5V~7.5V |
| Output Current per Channel | 220mA |
| Input Offset Voltage (Vos) | 12mV |
| Bandwidth | 350MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1000000 kHz |
| Voltage Gain | 68dB |
| Average Bias Current-Max (IIB) | 20μA |
| Power Supply Rejection Ratio (PSRR) | 58dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Settling Time | 22 ns |
| Low-Bias | NO |
| -3db Bandwidth | 325MHz |
| Programmable Power | NO |
| Max I/O Voltage | 3mV |
| Input Offset Current-Max (IIO) | 6μA |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 880μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
THS4215DRBR Overview
There is a 8-VDFN Exposed Pad case package that contains the instrumentation amplifiers. Op amps are Voltage Feedback types of amplifier on the chip. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. The number of terminations approaches 8. The pins on this board total to 8 in total. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. Instrumentation amplifier is a part of Operational Amplifier. Linear amplifier includes 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 12mV. Surface Mount is the recommended mounting type of operational amplifiers. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 19mA and 10 . Maintain 68dB as the voltage gain. There is an operating supply voltage rating of 1 for this operational amplifier, which is rated at the manufacturer. To pack the operational amplifier ics, TR is adopted as the packing method.
THS4215DRBR Features
8 Pins
supply voltage of 5V
68dB voltage gain
THS4215DRBR Applications
There are a lot of Texas Instruments THS4215DRBR Instrumentational OP Amps applications.
- Communication device
- Non-polarized electrodes
- single/dual op amp sum and difference circuits
- Proportional operation circuits
- Scintillation detectors
- Automation control systems
- Automatic control
- Laptop
- Weighing systems
- Weak signal detection
