THS4304DBVT
| Parameters | |
|---|---|
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | THS4304 |
| Pin Count | 5 |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Operating Supply Current | 18mA |
| Nominal Supply Current | 18.9mA |
| Power Dissipation | 391mW |
| Output Current | 100mA |
| Slew Rate | 830V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 7μA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5V ±1.35V~2.5V |
| Output Current per Channel | 140mA |
| Input Offset Voltage (Vos) | 4mV |
| Bandwidth | 3 GHz |
| Gain Bandwidth Product | 870MHz |
| Unity Gain BW-Nom | 3000000 kHz |
| Voltage Gain | 65dB |
| Power Supply Rejection Ratio (PSRR) | 73dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Settling Time | 4.5 ns |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Max I/O Voltage | 4mV |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Weight | 13.012431mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 391mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
THS4304DBVT Overview
Op amp is packaged in SC-74A, SOT-753 case. An op amp of this type is a Voltage Feedback-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. A total of 5 terminations have been reported in the past few weeks. It consists of a total of 5 pins in total. I would like to remind you that this buffer op amp should be powered by an 3V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. Linear amplifier includes 5 pins. With regard to input offset voltage, instrumentation amplifier is rated at 4mV. The mounting type that is recommended for this electrical part is Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . It is possible to operate this buffer amplifier from a supply current of 18mA . There should be no change in the voltage gain. As far as the device is concerned, buffer amplifier has 1 channels. The operating supply voltage of the buffer op amp is rated at 3V. TR is adopted to pack the instrumentation amplifier.
THS4304DBVT Features
5 Pins
supply voltage of 3V
65dB voltage gain
THS4304DBVT Applications
There are a lot of Texas Instruments THS4304DBVT Instrumentational OP Amps applications.
- earphone
- RF cable systems
- Band-stop filter
- Portable electronic products powered by batteries
- Broadcasting
- Addition operation circuits
- Proportional counter tubes
- Weak signal detection
- Test equipment
- Signal filtering
