THS4502ID
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 75.891673mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 50kOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 1.02W |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | THS4502 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 23mA |
| Nominal Supply Current | 28mA |
| Power Dissipation | 1.02W |
| Slew Rate | 2800V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 74 dB |
| Current - Input Bias | 4μA |
| Max Input Voltage | -1.3V |
| Voltage - Supply, Single/Dual (±) | 4.5V~15V ±2.25V~7.5V |
| Output Current per Channel | 120mA |
| Input Offset Voltage (Vos) | 2.4mV |
| Bandwidth | 370MHz |
| Gain Bandwidth Product | 300MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 300000 kHz |
| Voltage Gain | 54dB |
| Average Bias Current-Max (IIB) | 5.2μA |
| Power Supply Rejection Ratio (PSRR) | 72dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Settling Time | 6.3 ns |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 30MHz |
| Bias Current-Max (IIB) @25C | 4.6μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Max I/O Voltage | -4mV |
| Input Offset Current-Max (IIO) | 2μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
THS4502ID Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. There are two types of operational amplifiers in this circuit. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. During the past two weeks, there have been close to 8 terminations. Linear amplifier has a total of 8 pins. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. There are 8 pins on this chip. Regarding input offset voltage, op amp rates 2.4mV. This electronic part is recommended for mounting type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. Using a supply current of 23mA , this buffer op amp will be able to operate. The voltage gain should stay at 54dB. 1 channels are available on the instrumentation amplifier. The operating supply voltage of instrumentation amplifier is rated 5V voltage. Instrumentation amplifier resistance should remain within the range of 50kOhm.
THS4502ID Features
8 Pins
supply voltage of 5V
54dB voltage gain
Resistance of 50kOhm
THS4502ID Applications
There are a lot of Texas Instruments THS4502ID Instrumentational OP Amps applications.
- Proportional operation circuits
- Home audio systems
- Medical instruments
- Active probe
- Television broadcasting equipment
- Strain gauges
- Subtraction operation circuits
- Non-polarized electrodes
- Signal transformation
- Voltage regulation circuit
