THS4505DGK
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 23.303308mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 10MOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 385mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | THS4505 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Operating Supply Current | 16mA |
| Nominal Supply Current | 20mA |
| Power Dissipation | 385mW |
| Max Supply Current | 17mA |
| Slew Rate | 1800V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 74 dB |
| Current - Input Bias | 4μA |
| Max Input Voltage | -2.7V |
| Voltage - Supply, Single/Dual (±) | 4.5V~15V ±2.25V~7.5V |
| Output Current per Channel | 130mA |
| Input Offset Voltage (Vos) | 7mV |
| Bandwidth | 260MHz |
| Gain Bandwidth Product | 210MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 210000 kHz |
| Voltage Gain | 54dB |
| Average Bias Current-Max (IIB) | 5.2μA |
| Power Supply Rejection Ratio (PSRR) | 72dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 4mV |
| Settling Time | 20 ns |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 20MHz |
| Bias Current-Max (IIB) @25C | 4.6μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Max I/O Voltage | -7mV |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
THS4505DGK Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. The instrumentation amplifier in this picture is of the Differential-type. Linear amplifier is delivered in a Tube case. During the past two weeks, there have been close to 8 terminations. Linear amplifier has a total of 8 pins. Please take in mind that this instrumentation amplifier should be run at 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are available on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 7mV. For this electrical component, Surface Mount is the recommended mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureIt is possible to operate this buffer amplifier from a supply current of 16mA . There should be no change in the voltage gain. 1 channels are available on the instrumentation amplifier. It is recommended to keep the instrumentation amplifier resistance within the range of 10MOhm.
THS4505DGK Features
8 Pins
supply voltage of 5V
54dB voltage gain
Resistance of 10MOhm
THS4505DGK Applications
There are a lot of Texas Instruments THS4505DGK Instrumentational OP Amps applications.
- Logarithmic operation circuits
- RF cable systems
- Laptop
- Industrial control system
- Biopotential
- Semiconductor detectors
- Cinema or auditorium audio system
- Home audio systems
- Signal transformation
- Power generator
