TL032AIDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIFET |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TL032 |
| Pin Count | 8 |
| Number of Elements | 2 |
| Power Supplies | +-5/+-15V |
| Operating Supply Current | 434μA |
| Nominal Supply Current | 560μA |
| Output Current | 40mA |
| Slew Rate | 5.1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 2pA |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~15V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 390μV |
| Bandwidth | 1.1MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1100 kHz |
| Voltage Gain | 82.61dB |
| Average Bias Current-Max (IIB) | 0.0009μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.1MHz |
| Max I/O Voltage | 800μV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.0001μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL032AIDR Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. J-FET-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. In recent months, the number of terminations has approached 8. A total of 8 pins are attached to buffer op amp. This linear amplifier should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. There are 8 pins on this chip. In terms of input offset voltage, operational amplifier rates 390μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. An 434μA volt supply current is needed for this linear amplifier to operate. Keeping the voltage gain at 82.61dB is the best course of action. 2 elements make up the design of this buffer amplifier. A TR-shaped amplifier is used to pack the buffer amps.
TL032AIDR Features
8 Pins
supply voltage of 5V
82.61dB voltage gain
TL032AIDR Applications
There are a lot of Texas Instruments TL032AIDR Instrumentational OP Amps applications.
- Exponential operation circuits
- Hand-held batteries
- Addition operation circuits
- Fast A/D and D/A converters
- Thermocouples
- Mobile phone
- Weak signal detection
- Comparator
- Band-pass filter
- Fission chambers
