TL052IDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TL052 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Elements | 2 |
| Operating Supply Current | 4.8mA |
| Nominal Supply Current | 5.6mA |
| Slew Rate | 20.7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~15V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3300 kHz |
| Voltage Gain | 95.42dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 650μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 1.5mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.01μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL052IDR Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. The instrumentation amplifier in this picture is of the J-FET-type. There is a Cut Tape (CT) case that is delivered with the instrumentation amplifiers. A total of 8 terminations have been reported in the past few weeks. The total number of pins on linear amplifier is 8. Please take in mind that op amp should be run at 5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. There are 8 pins on this chip. Op amp rates 3.5mV as input offset voltage. This electronic part is best mounted with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 4.8mA and 10 . You should keep the voltage gain at 95.42dB for the time being. There are 2 elements in total in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 15V voltage. It is used TR to pack the op amps.
TL052IDR Features
8 Pins
supply voltage of 5V
95.42dB voltage gain
TL052IDR Applications
There are a lot of Texas Instruments TL052IDR Instrumentational OP Amps applications.
- Biopotential
- Inverse/same-phase proportional circuit
- Scintillation detectors
- Logarithmic operation circuits
- Signal transformation
- Test equipment
- Video computer boards
- Vehicle electronics
- Large motor controllers
- Automatic control
