TL054CN
| Parameters | |
|---|---|
| Nominal Gain Bandwidth Product | 2.7MHz |
| Max I/O Voltage | 4mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.001μA |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | TL054 |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Operating Supply Current | 8.4mA |
| Nominal Supply Current | 11.2mA |
| Slew Rate | 17.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~15V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 5.5mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3300 kHz |
| Voltage Gain | 97.15dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 560μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
TL054CN Overview
It is packaged in an 14-DIP (0.300, 7.62mm)-case that protects the operational amplifiers from damage. The instrumentation amplifier in this picture is of the J-FET-type. In the case of Tube cases, linear amplifier will be delivered. The number of terminations is approaching the 14 mark. The total number of pins on linear amplifier is 14. Please take in mind that this instrumentation amplifier should be run at 5V. It should be noted that this op amp is a type of Operational Amplifier device. An 14-pin op amp ic is included in the package. There is an input offset voltage of 5.5mV for this buffer op amp. For this electronic part, it is recommended that you mount it with type Through Hole. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. You can run this op amp ic on 8.4mA . It is a member of the 97.15dB's 97.15dB family. Buffer op amp is equipped with 4 channels on the device. The operating supply voltage of instrumentation amplifier is rated 15V voltage.
TL054CN Features
14 Pins
supply voltage of 5V
97.15dB voltage gain
TL054CN Applications
There are a lot of Texas Instruments TL054CN Instrumentational OP Amps applications.
- RF cable systems
- Addition operation circuits
- Large motor controllers
- Switching amplifier
- Weighing systems
- Micro signal measurement
- Digital cameras
- ECG equipment
- Commercial audio systems
- Broadcasting
