Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 4 days ago) |
Mounting Type |
Through Hole |
Package / Case |
14-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
14 |
Operating Temperature |
-40°C~85°C |
Packaging |
Tube |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Base Part Number |
TL054 |
Pin Count |
14 |
Operating Supply Voltage |
15V |
Number of Elements |
4 |
Operating Supply Current |
8.4mA |
Nominal Supply Current |
11.2mA |
Slew Rate |
17.8V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
J-FET |
Common Mode Rejection Ratio |
65 dB |
Current - Input Bias |
30pA |
Voltage - Supply, Single/Dual (±) |
10V~30V ±5V~15V |
Output Current per Channel |
80mA |
Input Offset Voltage (Vos) |
5.5mV |
Bandwidth |
2.7MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Unity Gain BW-Nom |
3300 kHz |
Voltage Gain |
97.15dB |
Average Bias Current-Max (IIB) |
0.0002μA |
Low-Offset |
NO |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
18V |
Voltage - Input Offset |
560μV |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.0002μA |
Programmable Power |
NO |
Nominal Gain Bandwidth Product |
2.7MHz |
Max I/O Voltage |
4mV |
Power |
NO |
Input Offset Current-Max (IIO) |
0.01μA |
Height |
5.08mm |
Length |
19.3mm |
Width |
6.35mm |
Thickness |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TL054IN Overview
In order to protect the op amps, a 14-DIP (0.300, 7.62mm) case is used. This is a J-FET type op amp. The op amp is delivered to you in a Tube case. There is a growing number of terminations approaching the number of 14. A total of 14 pins are attached to buffer op amp. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. There are 14 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 5.5mV. Through Hole is the recommended mounting type of operational amplifiers. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . This op amp can operate from a supply current at 8.4mA. You should keep the voltage gain at 97.15dB for the time being. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 4. The operating supply voltage of the buffer op amp is rated at 15V.
TL054IN Features
14 Pins
supply voltage of 5V
97.15dB voltage gain
TL054IN Applications
There are a lot of Texas Instruments TL054IN Instrumentational OP Amps applications.
- Signal filtering
- Large motor controllers
- Micro signal measurement
- Multiplication circuits
- Power generator
- ECG equipment
- Hand-held batteries
- Test equipment
- Power control
- Tablets