TL061ACDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TL061 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 1 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 250μA |
| Power Dissipation | 680mW |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 6mV |
| Gain Bandwidth Product | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 75.56dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Input Offset Current-Max (IIO) | 0.003μA |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
TL061ACDT Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. An op amp of this type is a J-FET-type. Instrumentation amplifier is delivered in a Cut Tape (CT) case. During the past two weeks, there have been close to 8 terminations. The total number of pins on linear amplifier is 8. Please take in mind that this instrumentation amplifier should be run at 15V. It should be noted that this op amp is a type of Operational Amplifier device. Linear amplifier includes 8 pins. There is an input offset voltage of 6mV for this buffer op amp. The mounting type that is recommended for this electrical part is Surface Mount. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. As long as the supply current of the chip does not exceed 200μA, this op amp ic can operate. Op amp is a member of the 75.56dB's 75.56dB family. It is possible to count 1 elements on this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
TL061ACDT Features
8 Pins
supply voltage of 15V
75.56dB voltage gain
TL061ACDT Applications
There are a lot of STMicroelectronics TL061ACDT Instrumentational OP Amps applications.
- Automation control systems
- E-book readers
- Laptop
- Communication
- Oscilloscopes
- Precision measurement
- earphone
- Tablets
- Scintillation detectors
- Home audio systems
