TL061ACP
| Parameters | |
|---|---|
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | TL061 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 250μA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 75.56dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 6mV |
| Input Offset Current-Max (IIO) | 0.003μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
TL061ACP Overview
The linear amplifier is packaged in a 8-DIP (0.300, 7.62mm) case which makes it easy for the consumer to handle. There are two types of operational amplifiers in this circuit. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. A total of 8 terminations have been reported in the past few weeks. In this case, there are 8 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. It should be noted that this op amp is a type of Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. In terms of input offset voltage, operational amplifier rates 3mV. For this electrical component, the recommended mounting type is Through Hole, which is the most common. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. An 200μA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 75.56dB for the time being. Buffer op amp is equipped with 1 channels on the device. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
TL061ACP Features
8 Pins
supply voltage of 15V
75.56dB voltage gain
TL061ACP Applications
There are a lot of Texas Instruments TL061ACP Instrumentational OP Amps applications.
- Thermocouples
- Fission chambers
- Automatic control
- Video data acquisition
- Semiconductor detectors
- Addition operation circuits
- Medical imaging
- Mobile phone
- Television broadcasting equipment
- Oscilloscopes
