TL061CDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TL061 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 1 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 250μA |
| Power Dissipation | 680mW |
| Output Current | 20mA |
| Min Input Voltage | -12V |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 30pA |
| Max Input Voltage | 15V |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 15mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 75.56dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0004μA |
| Dual Supply Voltage | 15V |
| Input Offset Current-Max (IIO) | 0.005μA |
| Height | 1.25mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL061CDT Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. This is a J-FET type op amp. Linear amplifier is delivered in a Cut Tape (CT) case. There is a growing number of terminations approaching the number of 8. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. An 8-pin op amp ic is included in the package. As far as the input offset voltage is concerned, linear amplifier rates at 15mV. Surface Mount is the recommended mounting type for this linear amplifier. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. A supply current of 200μA can be used to operate this linear amplifier. It is recommended to keep the voltage gain at 75.56dB at all times. 1 elements make up the design of this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage. It is used TAPE AND REEL to pack the op amps.
TL061CDT Features
8 Pins
supply voltage of 15V
75.56dB voltage gain
TL061CDT Applications
There are a lot of STMicroelectronics TL061CDT Instrumentational OP Amps applications.
- Test equipment
- Industrial control system
- Cinema or auditorium audio system
- High speed sample
- E-book readers
- Differentiator circuits
- Commercial audio systems
- Biopotential
- Vehicle electronics
- Ultrasound transducers
