TL061ID
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~105°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TL061 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 1 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 250μA |
| Power Dissipation | 680mW |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 75.56dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Length | 4.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL061ID Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. A J-FET-type buffer amplifier is shown here. In the case of Tube cases, linear amplifier will be delivered. The number of terminations approaches 8. A total of 8 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 15V volts. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. It has 8 pins that make up the linear amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 6mV. The mounting type that is recommended for this electrical part is Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~105°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 200μA and 10 . Keeping the voltage gain at 75.56dB is the best course of action. The op amp is rated for an operating supply voltage of 1. The operating supply voltage of the buffer op amp is rated at 18V.
TL061ID Features
8 Pins
supply voltage of 15V
75.56dB voltage gain
TL061ID Applications
There are a lot of STMicroelectronics TL061ID Instrumentational OP Amps applications.
- Industrial applications including automation
- Ultrasound transducers
- Active probe
- Power generator
- Video computer boards
- Computer workstations
- Professional videography
- Measurements of Wheatstone bridge
- Vehicle electronics
- Cinema or auditorium audio system
