TL061IDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | TL061 |
| Pin Count | 8 |
| Number of Elements | 1 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 250μA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 75.56dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 6mV |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL061IDR Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. Op amps are J-FET types of amplifier on the chip. Instrumentation amplifier is delivered in a Cut Tape (CT) case. In recent months, the number of terminations has approached 8. Linear amplifier has a total of 8 pins. Please take in mind that op amp should be run at 15V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The op amp ic has an array of 8 pins on it. In terms of the input offset voltage, instrumentation amplifier rates at 6mV. This electrical part should be mounted using type Surface Mount. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. The buffer amplifier is capable of operating from a supply current of 200μA . There should be no change in the voltage gain. This linear amplifier has a total of 1 elements. This linear amplifier pack is based on the TR axis.
TL061IDR Features
8 Pins
supply voltage of 15V
75.56dB voltage gain
TL061IDR Applications
There are a lot of Texas Instruments TL061IDR Instrumentational OP Amps applications.
- Industrial control system
- High/low-pass filter circuit
- Television
- Portable media players
- Signal operation
- RF cable systems
- Fast A/D and D/A converters
- Hand-held batteries
- Automotive sensors
- Strain gauges
