TL062IDR
| Parameters | |
|---|---|
| Micropower | YES |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 6mV |
| Input Offset Current-Max (IIO) | 0.0001μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | TL062 |
| Pin Count | 8 |
| Power Supplies | +-15V |
| Number of Channels | 2 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 500μA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 75.56dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
TL062IDR Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. An op amp of this type is a J-FET-type. Linear amplifier is delivered in a Cut Tape (CT) case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are located on this board. The linear amplifier should be run at 15V at all times, so please keep that in mind when using it. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are included on the operational amplifiers. Regarding input offset voltage, buffer amplifier rates 6mV voltage. For this electrical component, Surface Mount is the recommended mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . It is possible to operate this buffer amplifier from a supply current of 200μA . 75.56dB should remain the voltage gain. There are a total of 2 channels available on the op amps. It is used TR to pack the op amps.
TL062IDR Features
8 Pins
supply voltage of 15V
75.56dB voltage gain
TL062IDR Applications
There are a lot of Texas Instruments TL062IDR Instrumentational OP Amps applications.
- Video data acquisition
- Switching amplifier
- Weighing systems
- Signal amplification
- Thermocouples
- RF cable systems
- PDA
- Integrator circuits
- Wireless base stations
- Video computer boards
