Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 4 days ago) |
Mounting Type |
Through Hole |
Package / Case |
14-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
14 |
Operating Temperature |
0°C~70°C |
Packaging |
Tube |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Number of Functions |
4 |
Supply Voltage |
15V |
Base Part Number |
TL064 |
Pin Count |
14 |
Operating Supply Voltage |
18V |
Power Supplies |
+-15V |
Number of Channels |
4 |
Operating Supply Current |
200μA |
Nominal Supply Current |
1mA |
Slew Rate |
3.5V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
J-FET |
Common Mode Rejection Ratio |
80 dB |
Current - Input Bias |
30pA |
Voltage - Supply, Single/Dual (±) |
7V~36V ±3.5V~18V |
Input Offset Voltage (Vos) |
3mV |
Bandwidth |
1MHz |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Unity Gain BW-Nom |
1000 kHz |
Voltage Gain |
75.56dB |
Average Bias Current-Max (IIB) |
0.007μA |
Low-Offset |
NO |
Frequency Compensation |
YES |
Low-Bias |
YES |
Micropower |
YES |
Bias Current-Max (IIB) @25C |
0.0002μA |
Programmable Power |
NO |
Dual Supply Voltage |
9V |
Nominal Gain Bandwidth Product |
1MHz |
Max I/O Voltage |
3mV |
Input Offset Current-Max (IIO) |
0.0001μA |
Height |
5.08mm |
Length |
19.3mm |
Width |
6.35mm |
Thickness |
3.9mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TL064BCN Overview
The linear amplifier is packaged in a 14-DIP (0.300, 7.62mm) case which makes it easy for the consumer to handle. An op amp ic of the J-FET type. In the case of Tube cases, linear amplifier will be delivered. There is a growing number of terminations approaching the number of 14. In total, there are 14 pins on this op amp ic. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. Instrumentation amplifier is a part of Operational Amplifier. In total, the buffer amplifier consists of 14 pins. There is an input offset voltage of 3mV for this buffer op amp. This electronic component is recommended to be mounted using the mounting type Through Hole. With regard to operating temperature, this op amp functions well at 0°C~70°C. As long as the supply current of the chip does not exceed 200μA, this op amp ic can operate. 75.56dB should remain the voltage gain. On the buffer amps, there are 4 channels that can be used. The operating supply voltage of the buffer op amp is rated at 18V.
TL064BCN Features
14 Pins
supply voltage of 15V
75.56dB voltage gain
TL064BCN Applications
There are a lot of Texas Instruments TL064BCN Instrumentational OP Amps applications.
- Commercial audio systems
- Inverse/same-phase proportional circuit
- Measurements of Wheatstone bridge
- High-frequency data acquisition systems
- Mobile phone
- Test and measurement instruments
- Fission chambers
- Comparator
- Band-stop filter
- Oscilloscopes