TL064CD
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 4.535924g |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TL064 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 1mA |
| Power Dissipation | 680mW |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 15mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 75.56dB |
| Average Bias Current-Max (IIB) | 0.01μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | YES |
| Dual Supply Voltage | 9V |
| Height | 1.65mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
TL064CD Overview
In order to protect the op amps, a 14-SOIC (0.154, 3.90mm Width) case is used. A J-FET-type buffer amplifier is shown here. In the case of Tube cases, linear amplifier will be delivered. There have been a total of 14 terminations over the past year. The total number of pins on linear amplifier is 14. Please take in mind that this instrumentation amplifier should be run at 15V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 8 pins are located on the operational amplifiers. The input offset voltage is 15mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . An 200μA volt supply current is needed for this linear amplifier to operate. 75.56dB should be the voltage gain. Instrumentation amplifier has 4 channels on it. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
TL064CD Features
14 Pins
supply voltage of 15V
75.56dB voltage gain
TL064CD Applications
There are a lot of STMicroelectronics TL064CD Instrumentational OP Amps applications.
- Automation control systems
- Hand-held batteries
- Video data acquisition
- Portable docking station
- Band-pass filter
- RF cable systems
- Signal transformation
- Multiplication circuits
- Semiconductor detectors
- Differentiator circuits
