TL064IDRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TL064 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Number of Elements | 4 |
| Power Supplies | +-15V |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 1mA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 75.56dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 6mV |
| Input Offset Current-Max (IIO) | 0.0001μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL064IDRG4 Overview
It is packaged in an 14-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. An op amp of this type is a J-FET-type. A Tape & Reel (TR) case is used for delivering the op amp. A total of 14 terminations have been reported in the past few weeks. A total of 14 pins are located on this board. Please take in mind that op amp should be run at 15V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. An 14-pin op amp ic is included in the package. In terms of input offset voltage, operational amplifier rates 6mV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. The buffer amplifier is capable of operating from a supply current of 200μA . Maintain 75.56dB as the voltage gain. It is possible to count 4 elements on this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage. For packing the buffer amplifier, the TR-axis is adopted.
TL064IDRG4 Features
14 Pins
supply voltage of 15V
75.56dB voltage gain
TL064IDRG4 Applications
There are a lot of Texas Instruments TL064IDRG4 Instrumentational OP Amps applications.
- Oscilloscopes
- Professional videography
- Active probe
- Precision measurement
- Signal filtering
- Inverse/same-phase proportional circuit
- Mobile phone
- Automation control systems
- Differentiator circuits
- Comparator
