TL064INSR
| Parameters | |
|---|---|
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TL064 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Circuits | 4 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 1mA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 75.56dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 6mV |
| Input Offset Current-Max (IIO) | 0.0001μA |
| Height | 2mm |
| Length | 10.3mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
TL064INSR Overview
Packaged in a 14-SOIC (0.209, 5.30mm Width) case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. There is a growing number of terminations approaching the number of 14. In this case, there are 14 pins on the board. I would like to remind you that this buffer op amp should be powered by an 15V battery. Instrumentation amplifier is a part of Operational Amplifier. 14 pins are available on the instrumentation amplifier. Regarding input offset voltage, op amp rates 3mV. Surface Mount is the recommended mounting type of operational amplifiers. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 200μA and 10 . You should keep the voltage gain at 75.56dB for the time being. There are 4 circuits on op amps. The operating supply voltage of the buffer op amp is rated at 18V. A TR-shaped amplifier is used to pack the buffer amps.
TL064INSR Features
14 Pins
supply voltage of 15V
75.56dB voltage gain
TL064INSR Applications
There are a lot of Texas Instruments TL064INSR Instrumentational OP Amps applications.
- Blood pressure sensors
- Multimedia playback equipment
- Tablets
- Oscilloscopes
- earphone
- Multiplication circuits
- Displayers for aircraft and air transportation control systems
- Biopotential
- RF cable systems
- Inverse/same-phase proportional circuit
