TL071ACP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | TL071 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 65pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 6mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL071ACP Overview
Packaging for the buffer amplifier is in the form of a 8-DIP (0.300, 7.62mm) case. This is a J-FET type op amp. The op amp is delivered to you in a Tube case. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are located on the operational amplifiers. There is an input offset voltage of 6mV for this buffer op amp. Through Hole is the recommended mounting type for this linear amplifier. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. Using a supply current of 1.4mA , this buffer op amp will be able to operate. Op amp is a member of the 106.02dB's 106.02dB family. The op amp ic has 1 channels on it. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
TL071ACP Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL071ACP Applications
There are a lot of Texas Instruments TL071ACP Instrumentational OP Amps applications.
- Band-stop filter
- Scintillation detectors
- Power control
- Vehicle electronics
- Power generator
- Proportional counter tubes
- MP3
- Logarithmic operation circuits
- Radiation thermometry transducers
- High speed sample
