TL071ID
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | TL071 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 65pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 6mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL071ID Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. J-FET-type instrumentation amplifiers are used in this application. The op amp is delivered to you in a Tube case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. There are 8 pins on this chip. There is an input offset voltage of 6mV for this buffer op amp. For this electrical component, Surface Mount is the recommended mounting type. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. As long as the supply current of the chip does not exceed 1.4mA, this op amp ic can operate. There should be no change in the voltage gain at 106.02dB. 1 channels are available on the instrumentation amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
TL071ID Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL071ID Applications
There are a lot of Texas Instruments TL071ID Instrumentational OP Amps applications.
- Addition operation circuits
- Exponential operation circuits
- Car stereo
- Thermocouples
- Blood pressure sensors
- Tablets
- Television
- High gain DC amplifier
- Large motor controllers
- Semiconductor detectors
