TL071IDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | TL071 |
| Pin Count | 8 |
| Number of Elements | 1 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 65pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 6mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL071IDR Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. There are two types of operational amplifiers in this circuit. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are attached to buffer op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 8 pins on this chip. In terms of input offset voltage, operational amplifier rates 6mV. This electronic part is recommended for mounting type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. The buffer amplifier is capable of operating from a supply current of 1.4mA . 106.02dB should be the voltage gain. There is a rating of 1 for the operating supply voltage of the buffer op amp. The linear amplifier is packaged by using a TR axis.
TL071IDR Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL071IDR Applications
There are a lot of Texas Instruments TL071IDR Instrumentational OP Amps applications.
- pH (acidity)
- single/dual op amp sum and difference circuits
- Test and measurement instruments
- Test equipment
- Information processing
- Band-stop filter
- Signal amplification
- Integrator circuits
- High gain DC amplifier
- ECG equipment
