TL071IP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | TL071 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 65pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 6mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL071IP Overview
In the package, you will find a 8-DIP (0.300, 7.62mm)-case to contain the op amp ic. An op amp of this type is a J-FET-type. A Tube case is used to deliver the buffer op amp. The number of terminations is approaching the 8 mark. A total of 8 pins are attached to buffer op amp. Please take in mind that op amp should be run at 15V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are included on the operational amplifiers. The input offset voltage is 3mV. For this electronic part, it is recommended that you mount it with type Through Hole. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. It is possible to operate this buffer amplifier from a supply current of 1.4mA . The voltage gain should stay at 106.02dB. The op amp ic has 1 channels on it. The operating supply voltage of the buffer op amp is rated at 18V.
TL071IP Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL071IP Applications
There are a lot of Texas Instruments TL071IP Instrumentational OP Amps applications.
- Differentiator circuits
- Multimedia playback equipment
- Inverse/same-phase proportional circuit
- Thermocouples
- pH (acidity)
- Power transmission
- Communication
- Switching amplifier
- Measurements of Wheatstone bridge
- Oscilloscopes
