TL072ACDRG4
| Parameters | |
|---|---|
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 6mV |
| Power | NO |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | TL072 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 2 |
| Power Supplies | +-15V |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 5mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 65pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
TL072ACDRG4 Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. An op amp of this type is a J-FET-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins. The linear amplifier should be run at 15V at all times, so please keep that in mind when using it. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. An 8-pin op amp ic is included in the package. Op amp rates 6mV as input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. With regard to operating temperature, op amp ranges 0°C~70°C. It is possible to operate this buffer amplifier from a supply current of 1.4mA . There should be no change in the voltage gain. There are a total of 2 elements in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage. It is used TR to pack the op amps.
TL072ACDRG4 Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL072ACDRG4 Applications
There are a lot of Texas Instruments TL072ACDRG4 Instrumentational OP Amps applications.
- Micro signal measurement
- Video conversion and routing
- Proportional counter tubes
- Displayers for aircraft and air transportation control systems
- Comparator
- Automotive sensors
- Large motor controllers
- Television broadcasting equipment
- Active probe
- Power transmission
