TL072CDE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | TL072 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 2 |
| Power Supplies | +-15V |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 5mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 65pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 10mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.01μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL072CDE4 Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. An op amp of this type is a J-FET-type. Upon delivery, op amp ic is packaged in a Tube case. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are attached to buffer op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. This particular linear amplifier is a type of Operational Amplifier device, to be precise. The op amp ic has an array of 8 pins on it. Regarding input offset voltage, buffer amplifier rates 10mV voltage. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, this op amp functions well at 0°C~70°C. A supply current of 1.4mA can be used to operate this linear amplifier. 106.02dB should be the voltage gain. A voltage rating of 2 is indicated for the op amp's operating supply voltage. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
TL072CDE4 Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL072CDE4 Applications
There are a lot of Texas Instruments TL072CDE4 Instrumentational OP Amps applications.
- Precision measurement
- Inverse/same-phase proportional circuit
- Tablets
- Power transmission
- Hand-held batteries
- Strain gauges
- Portable electronic products powered by batteries
- Gaming industry
- Displayers for aircraft and air transportation control systems
- Oscilloscopes
