TL072CPSRE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | TL072 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Circuits | 2 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 5mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 65pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 10mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.01μA |
| Height | 2mm |
| Length | 6.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL072CPSRE4 Overview
The linear amplifier is packaged in a 8-SOIC (0.209, 5.30mm Width) case which makes it easy for the consumer to handle. A J-FET-type buffer amplifier is shown here. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are attached to buffer op amp. This linear amplifier should be powered by an 15V battery. It should be noted that this op amp is a type of Operational Amplifier device. Linear amplifier includes 8 pins. Regarding input offset voltage, op amp rates 3mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. It is possible to operate this buffer amplifier from a supply current of 1.4mA . It is a member of the 106.02dB's 106.02dB family. On this buffer amplifier, there are 2 circuits. The operating supply voltage of the buffer op amp is rated at 18V. The linear amplifier is packaged by using a TR axis.
TL072CPSRE4 Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL072CPSRE4 Applications
There are a lot of Texas Instruments TL072CPSRE4 Instrumentational OP Amps applications.
- Signal amplification
- Automotive sensors
- Strain gauges
- Voltage regulation circuit
- PDA
- Blood pressure sensors
- Division circuits
- Logarithmic operation circuits
- Radiation thermometry transducers
- Measurements of Wheatstone bridge
