TL074ACNSR
| Parameters | |
|---|---|
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 6mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 2mm |
| Length | 10.3mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TL074 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Circuits | 4 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 10mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 65pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 3mV |
TL074ACNSR Overview
The linear amplifier is packaged in a 14-SOIC (0.209, 5.30mm Width) case which makes it easy for the consumer to handle. A J-FET-type buffer amplifier is shown here. The op amp is delivered to you in a Tape & Reel (TR) case. There have been a total of 14 terminations over the past year. Buffer amplifier has a total of 14 pins. This linear amplifier should be powered by an 15V battery. Instrumentation amplifier is a part of Operational Amplifier. The op amp ic has an array of 14 pins on it. There is an input offset voltage of 3mV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. You can run this op amp ic on 1.4mA . There should be no change in the voltage gain. This op amp ic has 4 circuits. The operating supply voltage of the buffer op amp is rated at 18V. This linear amplifier pack is based on the TR axis.
TL074ACNSR Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
TL074ACNSR Applications
There are a lot of Texas Instruments TL074ACNSR Instrumentational OP Amps applications.
- Weak signal detection
- Television
- Computer workstations
- Scintillation detectors
- High input resistance broadband
- Information processing
- High-frequency data acquisition systems
- RF cable systems
- Digital cameras
- Portable media players
