TL074BCNE4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Package / Case | PDIP |
| Surface Mount | NO |
| Number of Pins | 14 |
| Packaging | Rail/Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | THROUGH-HOLE |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Number of Elements | 4 |
| Power Supplies | +-15V |
| Temperature Grade | COMMERCIAL |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 10mA |
| Slew Rate | 13 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 200pA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 3MHz |
| Gain Bandwidth Product | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 18V |
| Low-Bias | YES |
| Micropower | NO |
| Min Dual Supply Voltage | 3.5V |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 3mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
TL074BCNE4 Overview
There is a PDIP case in which the instrumentation amplifier is packaged. Buffer amps of this type are called OPERATIONAL AMPLIFIER-types. The case in which buffer amplifier is delivered is called a Rail/Tube case. A total of 14 terminations have been reported in the past few weeks. In this case, there are 14 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. Instrumentation amplifier is a part of Operational Amplifier. There are 14 pins on this chip. In terms of input offset voltage, operational amplifier rates 3mV. An 1.4mA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain at 106.02dB. For the buffer op amp to operate properly, it must be above the temperature of 0°C degrees Celsius. No temperature greater than 70°C should be used. The buffer op amp is rated for an operating voltage of 4 when it comes to the power supply. The operating supply voltage of the buffer op amp is rated at 18V. In order to conduct this part, you will need to provide dual supply voltages of 18V volts.
TL074BCNE4 Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
TL074BCNE4 Applications
There are a lot of Texas Instruments TL074BCNE4 Instrumentational OP Amps applications.
- single/dual op amp sum and difference circuits
- PDA
- MP3
- Division circuits
- RF cable systems
- Fast A/D and D/A converters
- High gain DC amplifier
- Professional videography
- Scintillation detectors
- Image computer boards
