Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 4 days ago) |
Contact Plating |
Gold |
Mounting Type |
Surface Mount |
Package / Case |
14-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
14 |
Operating Temperature |
0°C~70°C |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Base Part Number |
TL074 |
Pin Count |
14 |
Power Supplies |
+-15V |
Number of Channels |
4 |
Operating Supply Current |
1.4mA |
Nominal Supply Current |
10mA |
Slew Rate |
13V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
J-FET |
Common Mode Rejection Ratio |
70 dB |
Current - Input Bias |
65pA |
Voltage - Supply, Single/Dual (±) |
±5V~15V |
Input Offset Voltage (Vos) |
10mV |
Bandwidth |
3MHz |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Unity Gain BW-Nom |
3000 kHz |
Voltage Gain |
106.02dB |
Average Bias Current-Max (IIB) |
0.007μA |
Low-Offset |
NO |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
18V |
Voltage - Input Offset |
3mV |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.0002μA |
Programmable Power |
NO |
Dual Supply Voltage |
9V |
Neg Supply Voltage-Max (Vsup) |
-18V |
Nominal Gain Bandwidth Product |
3MHz |
Max I/O Voltage |
10mV |
Power |
NO |
Input Offset Current-Max (IIO) |
0.01μA |
Height |
1.75mm |
Length |
8.65mm |
Width |
3.91mm |
Thickness |
1.58mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TL074CDR Overview
Op amp is packaged in 14-SOIC (0.154, 3.90mm Width) case. J-FET-type instrumentation amplifiers are used in this application. A Tape & Reel (TR) case is used for delivering the op amp. A total of 14 terminations have been reported in the past few weeks. Linear amplifier has a total of 14 pins. Please take in mind that op amp should be run at 15V. It should be noted that this op amp is a type of Operational Amplifier device. 14 pins are located on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 10mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. With regard to operating temperature, this op amp functions well at 0°C~70°C. You can run this op amp ic on 1.4mA . There should be no change in the voltage gain at 106.02dB. 4 channels are available on the instrumentation amplifier. An buffer amplifier is packed in a TR-shape according to the design.
TL074CDR Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
TL074CDR Applications
There are a lot of Texas Instruments TL074CDR Instrumentational OP Amps applications.
- Instrumentation
- Ultrasound transducers
- High/low-pass filter circuit
- Broadcasting
- Large motor controllers
- Oscilloscopes
- Industrial control system
- Strain gauges
- Measurements of Wheatstone bridge
- Test equipment