TL074CPW
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | TL074 |
| Pin Count | 14 |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 10mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 65pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 10mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.01μA |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
TL074CPW Overview
In the package, you will find a 14-TSSOP (0.173, 4.40mm Width)-case to contain the op amp ic. An op amp of this type is a J-FET-type. A Tube case is used for delivering the op amp. There have been a total of 14 terminations over the past year. Linear amplifier has a total of 14 pins. Please take in mind that this instrumentation amplifier should be run at 15V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. An 14-pin op amp ic is included in the package. The input offset voltage is 10mV. Surface Mount is the recommended mounting type of operational amplifiers. It is important to note that this linear amplifier works well at a temperature of 0°C~70°C when it comes to operating temperatureYou can run this op amp ic on 1.4mA . There should be no change in the voltage gain. Buffer op amp is equipped with 4 channels on the device.
TL074CPW Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
TL074CPW Applications
There are a lot of Texas Instruments TL074CPW Instrumentational OP Amps applications.
- Oscilloscopes
- RF cable systems
- Weak signal detection
- Biopotential
- Industrial control system
- Differentiator circuits
- Laptop
- MP3
- Portable electronic products powered by batteries
- Automation control systems
