banner_page

TL074CPWR

4 Channels 65pA 70 dB Instrumentational OP Amps 0.007μA ±5V~15V TL074 14 Pins 14-TSSOP (0.173, 4.40mm Width)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-TL074CPWR
  • Package: 14-TSSOP (0.173, 4.40mm Width)
  • Datasheet: -
  • Stock: 196
  • Description: 4 Channels 65pA 70 dB Instrumentational OP Amps 0.007μA ±5V~15V TL074 14 Pins 14-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 5 days ago)
Contact Plating Gold
Mounting Type Surface Mount
Package / Case 14-TSSOP (0.173, 4.40mm Width)
Surface Mount YES
Number of Pins 14
Operating Temperature 0°C~70°C
Packaging Cut Tape (CT)
JESD-609 Code e4
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
ECCN Code EAR99
Subcategory Operational Amplifier
Packing Method TR
Technology BIPOLAR
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 15V
Base Part Number TL074
Pin Count 14
Power Supplies +-15V
Number of Channels 4
Operating Supply Current 1.4mA
Nominal Supply Current 10mA
Slew Rate 13V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type J-FET
Common Mode Rejection Ratio 70 dB
Current - Input Bias 65pA
Voltage - Supply, Single/Dual (±) ±5V~15V
Input Offset Voltage (Vos) 10mV
Bandwidth 3MHz
Neg Supply Voltage-Nom (Vsup) -15V
Unity Gain BW-Nom 3000 kHz
Voltage Gain 106.02dB
Average Bias Current-Max (IIB) 0.007μA
Low-Offset NO
Frequency Compensation YES
Supply Voltage Limit-Max 18V
Voltage - Input Offset 3mV
Low-Bias YES
Micropower NO
Bias Current-Max (IIB) @25C 0.0002μA
Programmable Power NO
Neg Supply Voltage-Max (Vsup) -18V
Nominal Gain Bandwidth Product 3MHz
Max I/O Voltage 10mV
Power NO
Input Offset Current-Max (IIO) 0.01μA
Height 1.2mm
Length 5mm
Width 4.4mm
Thickness 1mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

TL074CPWR Overview


Packaging for the buffer amplifier is in the form of a 14-TSSOP (0.173, 4.40mm Width) case. Op amps are J-FET types of amplifier on the chip. There is a Cut Tape (CT) case that is delivered with the instrumentation amplifiers. There is a growing number of terminations approaching the number of 14. Buffer amplifier has a total of 14 pins. It is important to remember that this op amp should be operated at a voltage of 15V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. A total of 14 pins are present on the instrumentation amplifier. Op amp rates 10mV as input offset voltage. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. An 1.4mA volt supply current is needed for this linear amplifier to operate. It is recommended to keep the voltage gain at 106.02dB at all times. Buffer op amp is equipped with 4 channels on the device. For packing the buffer amplifier, the TR-axis is adopted.

TL074CPWR Features


14 Pins
supply voltage of 15V
106.02dB voltage gain

TL074CPWR Applications


There are a lot of Texas Instruments TL074CPWR Instrumentational OP Amps applications.

  • Wireless base stations
  • Active probe
  • Weak signal detection
  • Computer workstations
  • Car stereo
  • Semiconductor detectors
  • Switching amplifier
  • Band-stop filter
  • Signal operation
  • Cinema or auditorium audio system

Write a review

Note: HTML is not translated!
    Bad           Good