TL074IDRE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TL074 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Number of Elements | 4 |
| Power Supplies | +-15V |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 10mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 65pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 10mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL074IDRE4 Overview
In order to protect the op amps, a 14-SOIC (0.154, 3.90mm Width) case is used. J-FET-type instrumentation amplifiers are used in this application. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. It is estimated that there will be 14 terminations in the next few months. Buffer amplifier has a total of 14 pins. I would like to remind you that this buffer op amp should be powered by an 15V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 14 pins are included on the operational amplifiers. There is an input offset voltage of 6mV for this buffer op amp. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. It is possible to operate this buffer amplifier from a supply current of 1.4mA . There should be no change in the voltage gain at 106.02dB. There are 4 elements in total in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage. The linear amplifier is packaged by using a TR axis.
TL074IDRE4 Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
TL074IDRE4 Applications
There are a lot of Texas Instruments TL074IDRE4 Instrumentational OP Amps applications.
- Car stereo
- Band-pass filter
- Large motor controllers
- Automation control systems
- Instrumentation
- Differentiator circuits
- Tablets
- Radar
- Semiconductor detectors
- Laptop
