TL081CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 680mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | TL081 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.8mA |
| Power Dissipation | 680mW |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 15mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0004μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 15mV |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL081CDR Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. A J-FET-type buffer amplifier is shown here. A Cut Tape (CT) case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. Please take in mind that op amp should be run at 15V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 8 pins are available on the instrumentation amplifier. Op amp ic rates 15mV for input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around 0°C~70°C . This op amp can operate from a supply current at 1.4mA. Maintain 106.02dB as the voltage gain. Op amp ic has 1 channels. TR is adopted to pack the instrumentation amplifier.
TL081CDR Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL081CDR Applications
There are a lot of Texas Instruments TL081CDR Instrumentational OP Amps applications.
- Fast A/D and D/A converters
- Active probe
- RF cable systems
- Video computer boards
- Communication device
- High speed sample
- Micro signal measurement
- Test equipment
- Inverse/same-phase proportional circuit
- Differentiator circuits
