TL081IDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~105°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TL081 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 1 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Power Dissipation | 680mW |
| Output Current | 40mA |
| Slew Rate | 16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Input Offset Current-Max (IIO) | 0.004μA |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL081IDT Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. Op amps are J-FET types of amplifier on the chip. As far as the packaging is concerned, buffer op amp is delivered in a Cut Tape (CT) case. In recent months, the number of terminations has approached 8. A total of 8 pins are located on this board. The linear amplifier should be run at 15V at all times, so please keep that in mind when using it. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. An 8-pin op amp ic is included in the package. Op amp ic rates 10mV for input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~105°C . Using an 1.4mA supply current, this operational amplifier ics can be operated. There should be no change in the voltage gain at 106.02dB. There are a total of 1 elements in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
TL081IDT Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL081IDT Applications
There are a lot of STMicroelectronics TL081IDT Instrumentational OP Amps applications.
- Comparator
- Information processing
- High/low-pass filter circuit
- Measurements of Wheatstone bridge
- High speed sample
- Band-stop filter
- Tablets
- Subtraction operation circuits
- Mobile phone
- Television broadcasting equipment
