TL082ACDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 680mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | TL082 |
| Pin Count | 8 |
| Power Supplies | +-15V |
| Number of Channels | 2 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 5.6mA |
| Power Dissipation | 680mW |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 6mV |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL082ACDR Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. This is a J-FET type op amp. A Cut Tape (CT) case is used for delivering the op amp. It is estimated that there will be at least 8 terminations this year. Buffer amplifier has a total of 8 pins. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. Instrumentation amplifier is a part of Operational Amplifier. There are 8 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 6mV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about 0°C~70°C . The buffer amplifier is capable of operating from a supply current of 1.4mA . Keeping the voltage gain at 106.02dB is the best course of action. Op amp ic has 2 channels. For the packing of the instrumentation amplifier, TR is adopted.
TL082ACDR Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL082ACDR Applications
There are a lot of Texas Instruments TL082ACDR Instrumentational OP Amps applications.
- Automatic control
- Television broadcasting equipment
- Portable media players
- Micro signal measurement
- High-frequency data acquisition systems
- Band-pass filter
- High input resistance broadband
- Portable docking station
- Integrator circuits
- Cinema or auditorium audio system
