banner_page

TL082ACDRE4

30pA 75 dB Instrumentational OP Amps 0.007μA 18V 7V~36V ±3.5V~18V TL082 8 Pins 8-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-TL082ACDRE4
  • Package: 8-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 376
  • Description: 30pA 75 dB Instrumentational OP Amps 0.007μA 18V 7V~36V ±3.5V~18V TL082 8 Pins 8-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Lifecycle Status ACTIVE (Last Updated: 3 days ago)
Mounting Type Surface Mount
Package / Case 8-SOIC (0.154, 3.90mm Width)
Surface Mount YES
Number of Pins 8
Operating Temperature 0°C~70°C
Packaging Tape & Reel (TR)
JESD-609 Code e4
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Operational Amplifier
Packing Method TR
Technology BIPOLAR
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 15V
Base Part Number TL082
Pin Count 8
Operating Supply Voltage 18V
Number of Elements 2
Power Supplies +-15V
Operating Supply Current 1.4mA
Nominal Supply Current 5.6mA
Power Dissipation 680mW
Slew Rate 13V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type J-FET
Common Mode Rejection Ratio 75 dB
Current - Input Bias 30pA
Voltage - Supply, Single/Dual (±) 7V~36V ±3.5V~18V
Input Offset Voltage (Vos) 6mV
Bandwidth 3MHz
Neg Supply Voltage-Nom (Vsup) -15V
Unity Gain BW-Nom 3000 kHz
Voltage Gain 106.02dB
Average Bias Current-Max (IIB) 0.007μA
Low-Offset NO
Frequency Compensation YES
Voltage - Input Offset 3mV
Low-Bias YES
Micropower NO
Programmable Power NO
Nominal Gain Bandwidth Product 3MHz
Max I/O Voltage 6mV
Height 1.75mm
Length 4.9mm
Width 3.91mm
Thickness 1.58mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free
Factory Lead Time 1 Week

TL082ACDRE4 Overview


The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. J-FET-type instrumentation amplifiers are used in this application. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. The number of terminations approaches 8. In this case, there are 8 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. It has 8 pins that make up the linear amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 6mV. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, op amp ranges 0°C~70°C. An 1.4mA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 106.02dB for the time being. 2 elements make up the design of this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage. To pack the operational amplifier ics, TR is adopted as the packing method.

TL082ACDRE4 Features


8 Pins
supply voltage of 15V
106.02dB voltage gain

TL082ACDRE4 Applications


There are a lot of Texas Instruments TL082ACDRE4 Instrumentational OP Amps applications.

  • Multiplication circuits
  • Inverse/same-phase proportional circuit
  • ECG equipment
  • Laptop
  • Television
  • Hand-held batteries
  • Portable media players
  • Video data acquisition
  • Integrator circuits
  • Measurements of Wheatstone bridge

Write a review

Note: HTML is not translated!
    Bad           Good