TL082IPE4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Package / Case | PDIP |
| Surface Mount | NO |
| Number of Pins | 8 |
| Packaging | Rail/Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | THROUGH-HOLE |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 2 |
| Power Supplies | +-15V |
| Temperature Grade | INDUSTRIAL |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 5.6mA |
| Slew Rate | 13 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 200pA |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 3MHz |
| Gain Bandwidth Product | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 18V |
| Low-Bias | YES |
| Micropower | NO |
| Min Dual Supply Voltage | 3.5V |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 6mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.01μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
TL082IPE4 Overview
Op amp is packaged in PDIP case. Op amps are OPERATIONAL AMPLIFIER types of amplifier on the chip. The case in which buffer amplifier is delivered is called a Rail/Tube case. The number of terminations approaches 8. In total, there are 8 pins on this op amp ic. I would like to remind you that this buffer op amp should be powered by an 15V battery. Instrumentation amplifier is a part of Operational Amplifier. An 8-pin op amp ic is included in the package. Regarding input offset voltage, buffer amplifier rates 6mV voltage. You can run this op amp ic on 1.4mA . 106.02dB should be the voltage gain. For the buffer op amp to operate properly, it must be above the temperature of -40°C degrees Celsius. In order to avoid damage to the product, operational amplifiers should only be used at temperatures below 85°C. There is an operating supply voltage rating of 2 for this operational amplifier, which is rated at the manufacturer. The operating supply voltage of the buffer op amp is rated at 18V. In order for this electronic part to be conducted successfully, you should use a dual supply voltage of 18V.
TL082IPE4 Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL082IPE4 Applications
There are a lot of Texas Instruments TL082IPE4 Instrumentational OP Amps applications.
- Signal filtering
- Signal transformation
- Automotive sensors
- Navigation
- Test and measurement instruments
- Vehicle electronics
- Thermocouples
- Television broadcasting equipment
- High/low-pass filter circuit
- Logarithmic operation circuits
