TL082QDRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | TL082 |
| Pin Count | 8 |
| Number of Elements | 2 |
| Power Supplies | +-15V |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 5.6mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 6mV |
| Power | NO |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL082QDRQ1 Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. Buffer amps of this type are called J-FET-types. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. A total of 8 terminations have been reported in the past few weeks. In total, there are 8 pins on this op amp ic. I would like to remind you that this buffer op amp should be powered by an 15V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. Op amp ic rates 6mV for input offset voltage. This electronic part is best mounted with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . An 1.4mA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 106.02dB. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2. For the packing of the instrumentation amplifier, TR is adopted. Automotive, AEC-Q100 corresponds to linear amplifier's series.
TL082QDRQ1 Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
TL082QDRQ1 Applications
There are a lot of Texas Instruments TL082QDRQ1 Instrumentational OP Amps applications.
- Displayers for aircraft and air transportation control systems
- Measurements of Wheatstone bridge
- Signal transformation
- Hand-held batteries
- Biopotential
- Fission chambers
- Radiation thermometry transducers
- Power control
- Gaming industry
- Cinema or auditorium audio system
