TL084ACD
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | TL084 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Power Dissipation | 680mW |
| Output Current | 40mA |
| Slew Rate | 16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 4MHz |
| Rise Time | 50ns |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL084ACD Overview
Packaging for the buffer amplifier is in the form of a 14-SOIC (0.154, 3.90mm Width) case. J-FET-type instrumentation amplifiers are used in this application. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. The number of terminations is approaching the 14 mark. A total of 14 pins are attached to buffer op amp. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. Instrumentation amplifier is a part of Operational Amplifier. An 14-pin op amp ic is included in the package. As far as the input offset voltage is concerned, linear amplifier rates at 6mV. This electronic part is best mounted with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. As long as the supply current of the chip does not exceed 1.4mA, this op amp ic can operate. 106.02dB should remain the voltage gain. Instrumentation amplifier has 4 channels on it. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
TL084ACD Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
TL084ACD Applications
There are a lot of STMicroelectronics TL084ACD Instrumentational OP Amps applications.
- Automation control systems
- Precision measurement
- Signal filtering
- Fission chambers
- Signal transformation
- Radar
- Micro signal measurement
- Information processing
- Commercial audio systems
- RF cable systems
